Vent, Valve & Volt
No hot water at one faucet, but hot everywhere else

You can fix this

Likely cause: a stuck or clogged cartridge

A single-handle faucet that stays cold all the way across has a cartridge that is clogged on the hot side or stuck. Clean it, flush the valve body, or replace it.

Why this happens

In a single-handle faucet, one cartridge mixes hot and cold. Moen says when only hot or only cold has less than normal flow, replace the cartridge or clean the in-line filters on models that have them. Pfister's check is to pull the cartridge and look for debris in it and in the faucet housing. Moen says mineral build-up and loose debris can collect inside the valve body and obstruct the flow of water.

How to fix it

  1. Moen single-handle wall-mount tub filler whose handle stops short of full hot: check this first, before you take anything apart. It has a gray temperature limit stop under the handle that you reposition with needle-nose pliers. Moen says it is generally not recommended to exceed 120F, so check the water with a thermometer after each change.
  2. Shut off both stops by turning them clockwise by hand. If there are no stops, Moen says the shutoffs may be in an access panel around the tub, or you may need the main shutoff for the whole home. If a stop or the main will not turn by hand, do not force it; call a plumber. This Old House's plumbing expert warns against forcing a stuck main shutoff. Then open the faucet to make sure the water is off, and close the drain.
  3. Remove the handle. Pfister says a set-screw handle takes a 3/32 inch Allen wrench; others twist off counterclockwise.
  4. Pfister faucets with a retainer ring: unscrew the retainer ring counterclockwise, pull the cartridge straight up, wipe out debris, and soak a clogged cartridge in warm water for 30 minutes, as Pfister suggests.
  5. Moen 1225: slide out the copper clip, use the plastic twisting tool to turn the cartridge a quarter turn to loosen it, then pull the stem with pliers. Moen says this may take some effort.
  6. Before a new cartridge goes in, Moen recommends scrubbing the valve body with a nylon brush and flushing it: with a towel around the faucet base and a large bowl held upside down over the open body, have a helper open each stop slightly, one at a time. Moen warns the water can come out with considerable force. Blot out the water left at the bottom or the cartridge will not seat.
  7. Install the new cartridge with its tabs lined up with the cutouts in the body. Slide the clip back in without forcing it, and set the stem notch for hot on the left.

When to stop. If the 1225 stem pulls out and the shell stays stuck, Moen's fix needs a 1/2 inch 13 NC or 1/2 inch 20 NF tap wrench and a 3/8 inch hardwood dowel cut 1-3/4 inch long. If you do not have those, or the shell keeps spinning in the valve body, stop and call a plumber.

The part that fixes it

Match the cartridge to your valve before you order. Moen says the 1225 is commonly used in Moen single-handle faucets made before 2009, with the date varying by style and model; the ceramic cartridges fit the brands listed on each.

Replacement for Moen 1225 and 1200 Brass Cartridge

  • Single-handle kitchen, bath and tub faucets.

FourHome is our sister brand. We earn from purchases made through this link.

Replacement for Moen 1225 and 1225B Push-Pull Cartridge Kit

FourHome is our sister brand. We earn from purchases made through this link.

Cartridge Puller Tool for Moen 1200 and 1225 Cartridges

FourHome is our sister brand. We earn from purchases made through this link.

Replacement for Glacier Bay 169-640 35mm Cartridge

  • Also fits AquaSource single-handle faucets.

FourHome is our sister brand. We earn from purchases made through this link.

Not sure which part you have? Pull the old one and match it by brand, length and broach on Stems & Cartridges, an identification index of faucet stems and cartridges by part number.

If this does not fix it, tell the plumber

  • A single-handle faucet runs cold all the way across while other faucets are hot.
  • Whether you cleaned or replaced the cartridge and flushed the valve body.
  • The faucet brand and model, or a photo of the cartridge.

Build the full list: what to tell the plumber.

Not quite what you are seeing? Other results in this troubleshooter: Gas smell: leave the house now; the water heater, not this faucet; a frozen hot line; debris knocked loose into a screen; the hot stop is not fully open; the cartridge is turned backward; a worn, broken or reversed hot stem; Call a plumber: the hot stop is stuck or leaking.

Start this troubleshooter over

FourHome is our sister brand. Browse all FourHome replacement faucet and shower parts on the FourHome Amazon store. We earn from purchases made through this link.