You can fix this
Likely cause: a worn seat washer
A faucet that still drips from the spout a minute after you shut it off has a worn seat washer, or a loose screw holding it. Replacing the washer on the end of the stem fixes most of them.
Why this happens
Prier says a frost-free faucet shuts off inside the heated part of the house and the water left in the body drains out the spout, so a drip for up to 60 seconds after shutoff is normal. Past that, Prier says the seat washer most likely needs replacing. Woodford adds that a loose retainer screw on the washer causes the same drip. On a frost-free faucet the washer sits on the far end of a long stem, Family Handyman notes; on a short standard hose bib it is held at the base of the stem by a screw, the Saving Water Partnership says.
How to fix it
- Check your faucet's instruction sheet first. Legend's sheet for its T-550 sillcock says not to disassemble or service it at all, and to call a licensed contractor if it fails. If you have a T-550, or your sheet says the same, stop here and call a licensed plumber.
- Shut off the water to the faucet at its inside valve (usually in the basement or crawl space) or at the main. Turn it by hand only. Open the outdoor faucet to drain it.
- Remove the handle screw and handle, then the packing nut or head nut. On its Model 20, 25 and 27 faucets, Woodford says to turn the handle counterclockwise to full open first, and that the head nut has left-hand threads and comes off by turning clockwise; if a nut will not budge, check your brand's sheet before you lean on it.
- Put the handle back on loosely and use it to turn the stem counterclockwise until it comes free, as Woodford and Family Handyman describe. Woodford says a check valve on some stems adds drag, so pull the stem out with one swift pull. On a Woodford Model 20, 25 or 27 the rod pulls straight out once the head nut is off; Woodford says a nozzle drip on a new installation is most likely debris in the seat, so inspect the plunger for damage and flush the casing before you put it back.
- Snap a photo of the parts in order. Replace the washer with a matching one (the Saving Water Partnership suggests taking the old one to a plumbing supply store), and snug the retainer screw. On its Model 20, 25 and 27 faucets, Woodford says not to over-tighten parts on the rod, or it can break at the threads, and not to lubricate any of the parts.
- Slide the stem back in, hold the faucet body still with one hand, and tighten without over-tightening, as the Saving Water Partnership advises. Reinstall the handle, turn the water back on, shut the faucet and time the drip.
When to stop. Family Handyman says that if a new washer starts leaking again after a short time, the valve seat is worn and the whole faucet should be replaced; Woodford says the same about a damaged seat. A soldered faucet takes a torch to replace, so that is a job for a licensed plumber. If the inside valve will not close by hand, do not force it.
If this does not fix it, tell the plumber
- The faucet keeps dripping from the spout more than a minute after it is shut off.
- Whether you replaced the seat washer and how soon the drip came back.
- The brand, the body length if it is frost-free, and whether it is threaded or soldered to the pipe.
Build the full list: what to tell the plumber.
Not quite what you are seeing? Other results in this troubleshooter: Split pipe inside the wall: call a plumber; a frozen outdoor faucet; a loose or worn packing; a fouled or cracked vacuum breaker; Worn seat or broken stem: call a plumber; Probably normal: a short spurt or drip.
Start this troubleshooter over
FourHome is our sister brand. Browse all FourHome replacement faucet and shower parts on the FourHome Amazon store. We earn from purchases made through this link.